Collecting · Identification

Is xenotime magnetic?

Xenotime, the phosphate species Y(PO4), hardness 4–5, is paramagnetic on its sheet; USGS draws it at 0.30–0.70 amps, magnetite at 0.01. No iron in its crystal.

Short answer Moderately, not like magnetite. The xenotime-(Y) sheet prints “Paramagnetic”; USGS separator figures put the mineral in the paramagnetic class, not the ferromagnetic one. No specimen is tested hereThe mineral Xenotime-(Y), Y(PO4) on the IMA list (Rn, 1987 s.p., Norway): a phosphate species; tetragonal prismatic crystal habit; cleavage {100} good; hardness 4–5; density 4.4–5.1; vitreous to resinous lustre; 48.35% yttrium by mass; no iron in the formula; locality list from Norway to BrazilThe sheet’s words Xenotime-(Y): “Paramagnetic; may exhibit yellow cathodoluminescence.” The xenotime-(Yb) sheet prints no magnetic property; no sheet exists for xenotime-(Gd)USGS OFR 99-529, Table 1 Xenotime, 3 samples: 0.30–0.70 A in total, best 0.40–0.50 A, on a Frantz isodynamic separator, 15° side tilt, 125–150 µm grains. Magnetite best 0.01 AUSGS on rare-earth minerals “Although rare-earth metals like neodymium and samarium are known to be used in constructing powerful magnets, minerals containing rare-earth elements are only moderately paramagnetic (see bastnaesite, monazite, and xenotime)”The iron-free ledger Of 378 Table 1 rows, 18 match an IMA mineral with a rare-earth element in its formula; 13 of those have no iron in any matching formula. Median best-range midpoint: 0.65 A iron-free, 0.45 A iron-bearingWhere xenotime sits Best range 0.40–0.50 A, second-lowest of the 13 iron-free rows after britholite-(Y) at 0.40 (one sample). All 18 rows fall between 0.10 and 1.00 ADocumented failure Xenotime’s 0.30–0.70 A lies wholly inside monazite’s 0.30–1.00 A (8 samples), and its best range equals allanite’s: a separator does not tell them apartNot on this page Any hand-magnet test (no source fetched tested one), and any radioactivity, dose or handling content

Moderately, not like magnetite. The xenotime-(Y) sheet prints “Paramagnetic”, and USGS drew 3 xenotime samples on a laboratory separator at 0.30–0.70 amp, best 0.40–0.50; magnetite’s best was 0.01. Xenotime, Y(PO4), hardness 4–5, has no iron in its formula, and USGS calls rare-earth minerals “only moderately paramagnetic”.

In short

  • The verdict. The Handbook xenotime-(Y) sheet prints “Paramagnetic”. Table 1 of USGS Open-File Report 99-529 gives xenotime a total range of 0.30–0.70 amps, best 0.40–0.50, over 3 samples. The report defines paramagnetic as “less magnetic than ferromagnetic, and separable in magnetic separators with field currents up to 1.70 amps”. Ferromagnetic minerals are “strongly attracted to a magnet, like a piece of iron”; magnetite comes off at 0.01 amp.
  • The iron-free ledger. Matched by script to the September 2026 IMA-CNMNC Master List, 18 of Table 1’s 378 rows are minerals with a rare-earth element in the formula. 13 have no iron in any matching formula, xenotime among them, and every one is still drawn between 0.10 and 1.00 amp. Their median best-range midpoint is 0.65 amp against 0.45 for the 5 iron-bearing rows. Xenotime, at 0.40–0.50, is the second-earliest of the iron-free 13.
  • Documented failure: monazite and allanite. Xenotime’s total range, 0.30–0.70, sits wholly inside monazite’s 0.30–1.00 over 8 samples, and its best range, 0.40–0.50, is identical to allanite’s. A separator cannot sort these rare-earth minerals from one another, and 3 samples is a thin basis for any range.
  • Where magnetism does help. Against the other heavy minerals of a sand, the same table puts magnetite at under 0.01–0.05 amp, ilmenite at 0.025–0.40, rutile at 0.80 to over 1.70 and zircon above 1.70. The USGS Mineral Commodity Summaries 2026, Yttrium reports “Monazite concentrates containing yttrium-rich xenotime” from Florida heavy-mineral-sand operations.
  • The other questions. The xenotime-(Y) sheet prints no radioactivity line; routing is in the last section. Its Distribution field opens “Numerous localities but fine crystals are unusual”. USGS gives yttrium’s leading uses as ceramics and phosphors.
The iron-free ledger: every row of USGS Open-File Report 99-529, Table 1 (Rosenblum and Brownfield; Frantz isodynamic separator, 15° side tilt, 125–150 µm grains) whose name matches, by script, a September 2026 IMA row with a rare-earth element (Sc, Y, La–Lu) in its formula, ordered by best range, with four reference minerals below. “Iron” means Fe appears in any matching IMA formula. Polycrase, which has no row on the 2026 list, is not included
Table 1 nameMatching IMA formula(s)Iron in formula?Total range (amps)Best range (amps)Samples
GadoliniteCe2/Nd2/Y2 Fe2+Be2O2(SiO4)2Yes0.20–0.600.20–0.404
DaviditeCe/La(Y,U)Fe2(Ti,Fe,Cr,V)18(O,OH,F)38Yes0.10–0.600.30–0.503
Britholite-(Y)(Y,Ca)5(SiO4)3(OH)No0.20–0.500.401
SamarskiteYFe3+Nb2O8; YbNbO4Yes0.10–0.800.30–0.605
AllaniteCaREE(Al2Fe2+)(Si2O7)(SiO4)O(OH)Yes0.20–0.800.40–0.507
ChevkiniteCe4(Ti,Fe2+,Fe3+)5(Si2O7)2O8Yes0.10–0.600.40–0.501
XenotimeY(PO4), Yb(PO4), Gd(PO4)No0.30–0.700.40–0.503
FergusoniteYNbO4; CeNbO4·0.3H2ONo0.30–0.800.40–0.604
EuxeniteY(NbTi)O6No0.10–0.900.50–0.604
Ningyoite(U,Ca,Ce)2(PO4)2·1-2H2ONo0.30–0.900.601
Cerite(Ce7Ca2)☐Mg(SiO4)3(SiO3OH)4(OH)3No0.30–1.000.60–0.705
Fluocerite-(La)LaF3No0.40–0.900.60–0.701
MonaziteCe/La/Nd/Sm/Gd(PO4)No0.30–1.000.50–0.808
ParisiteCaCe2/La2/Nd2(CO3)3F2No0.50–0.900.701
AeschyniteCe/Nd/Y(TiNb)O6No0.50–1.00.70–0.802
HuanghoiteBaCe/BaNd(CO3)2FNo0.50–1.000.70–0.801
BastnaesiteCe/La/Nd/Y(CO3)FNo0.50–1.000.70–0.904
ThortveititeSc2Si2O7No0.60–1.000.80–0.901
Reference: magnetiteFe2+Fe3+2O4Yes<0.01–0.050.016
Reference: ilmeniteFe2+Ti4+O3Yes0.025–0.400.20–0.308
Reference: rutileTiO2No0.80–>1.70>1.7010
Reference: zirconZr(SiO4)No>1.70>1.705

Is xenotime magnetic? What the sheet and USGS say

The sheet. The xenotime-(Y) sheet, under physical properties, prints “Paramagnetic; may exhibit yellow cathodoluminescence.” That is the whole of its magnetic statement. The xenotime-(Yb) sheet prints no magnetic property, and no Handbook sheet exists for xenotime-(Gd), the third xenotime species on the September 2026 IMA list.

The separator. Rosenblum and Brownfield ran 1084 samples of 378 species through Frantz isodynamic separators, stepping the current up by 0.10 amp. Their Table 1 gives xenotime a total range of 0.30–0.70 amp and a best range, “the extraction range which contains the greatest amount of the desired mineral concentrate”, of 0.40–0.50 over 3 samples. Ferromagnetic magnetite comes off at 0.01. The report’s definitions put xenotime in the paramagnetic class, as the sheet does. A hand magnet is a different instrument, and no source fetched for this page tested one on xenotime. The species page is at xenotime.

Why is an iron-free mineral magnetic at all? The rare-earth ledger

USGS’s own sentence. The report says: “Other than iron, only manganese and copper have been noted to affect minerals that are extracted in the paramagnetic range.” It adds: “Although rare-earth metals like neodymium and samarium are known to be used in constructing powerful magnets, minerals containing rare-earth elements are only moderately paramagnetic (see bastnaesite, monazite, and xenotime).” Xenotime-(Y), Y(PO4), holds 48.35% yttrium by mass and no iron.

The ledger, method. All 378 Table 1 rows were parsed from the report’s PDF. Each name was matched to the September 2026 IMA list by exact name or root name plus suffix, and kept if any matching formula contains Sc, Y or a lanthanide. That gives 18 rows. Thirteen have no iron in any matching formula: aeschynite, bastnaesite, britholite-(Y), cerite, euxenite, fergusonite, fluocerite-(La), huanghoite, monazite, ningyoite, parisite, thortveitite and xenotime. All 18 are drawn between 0.10 and 1.00 amp; none reaches magnetite’s range or zircon’s. The iron-free rows’ best ranges centre on a median of 0.65 amp, the five iron-bearing rows’ on 0.45. Iron is not needed for xenotime to be drawn; in this ledger the iron-bearing rare-earth rows simply come off earlier on the median.

Can a magnet separate xenotime from monazite?

Documented failure. No. Xenotime’s total range, 0.30–0.70 amp, lies wholly inside monazite’s 0.30–1.00, and the best ranges, 0.40–0.50 and 0.50–0.80, touch at 0.50. Allanite’s best range is the same 0.40–0.50. The monazite-(Ce) sheet prints “Paramagnetic” too. The report warns that “micro-inclusions of magnetite or other ferromagnetic minerals” blur the lower limit, and three samples define xenotime’s whole row.

What does separate them. Structure and optics, as set out on the species pages: Monazite is monoclinic and biaxial, xenotime tetragonal and uniaxial. The magnetism of the other rare-earth species is covered on bastnäsite and allanite.

Where a separator does help: xenotime in a heavy-mineral sand

The heavy-sand neighbours. The USGS Mineral Commodity Summaries 2026, Yttrium reports that “Monazite concentrates containing yttrium-rich xenotime were produced from heavy-mineral-sand operations in Florida”, and the xenotime sheet calls it “a common detrital mineral in placers”. In such a sand, Table 1 orders the families, with some overlap. Magnetite comes off at under 0.01–0.05 amp and ilmenite at 0.025–0.40, best 0.20–0.30. Xenotime and monazite follow at 0.30–1.00, the bottom 0.10 amp shared with ilmenite’s total range. Rutile needs 0.80 to over 1.70 amps, and zircon is not drawn at 1.70.

The general picture. The site’s overview is at which minerals are magnetic. Other separator pages take different routes: is ilmenite magnetic for a titanium-bearing ore mineral, is franklinite magnetic for the spinels and is staurolite magnetic for a schist suite. More guides are in the collecting guides.

Is xenotime radioactive, rare, or useful?

Radioactive. The xenotime-(Y) sheet prints no radioactivity line, and the IMA formula Y(PO4) holds no thorium or uranium. The thorium and uranium figures from its analyses are on the species page. Radioactivity questions are routed to is my mineral radioactive and how to store radioactive mineral specimens; nothing here is health, safety or legal advice.

Rare, and used for. The sheet’s Distribution field opens “Numerous localities but fine crystals are unusual”, then names Norway, Ytterby in Sweden, the Swiss Alps, the Pamirs, Madagascar, Japan, Minas Gerais and Bahia in Brazil, and North Carolina placers. The USGS Mineral Commodity Summaries 2026, Yttrium gives yttrium’s leading uses as “ceramics and phosphors”, and that “Large resources of yttrium in monazite and xenotime are available worldwide”. This page makes no further use claim. Nothing on this site is offered for sale; the wanted list is the only commercial route.

Questions

Is xenotime magnetic?
Paramagnetic, on its sheet. USGS Open-File Report 99-529 drew 3 samples at 0.30–0.70 amps, best 0.40–0.50, against magnetite’s 0.01.
Will a fridge magnet pick up xenotime?
No source fetched for this page tested a hand magnet on xenotime. USGS classes it as paramagnetic, not ferromagnetic, the class “strongly attracted to a magnet, like a piece of iron”.
Does xenotime contain iron?
Not in its IMA formula, Y(PO4). It is still drawn at 0.30–0.70 amps, as are 12 other iron-free rare-earth rows in USGS Table 1.
Can magnetism separate xenotime from monazite?
No. Xenotime’s 0.30–0.70 amps lies inside monazite’s 0.30–1.00. Crystal system and optics separate them: tetragonal and uniaxial against monoclinic and biaxial.
What is xenotime used for?
It is a source of yttrium. The USGS 2026 yttrium summary names yttrium resources in monazite and xenotime, and gives yttrium’s leading uses as ceramics and phosphors.