Species · Oxides

Tenorite

Tenorite is CuO, copper(II) oxide: monoclinic, steel-grey to black, metallic, hardness 3.5, density 6.45, 79.89% copper, set against the black copper sulfides.

Formula (IMA, September 2026) CuO; status A, 1962 s.p.; country Italy. The Handbook sheet writes CuO and calls it “Nearly pure CuO; modern analyses are not available”Composition, worked Cu 79.89%, O 20.11% by mass (formula mass 79.55); copper as Cu2+ by charge balance against O2−Crystal system and habit Monoclinic, point group 2/m, space group C2/c; lathlike crystals flattened on [100], elongated along [011], to 2 mm; curved, scaly, dendritic; commonly pulverulent, earthy, massiveTwinning On {011}, contact plane, common, forming stellate groups; lamellarHardness, density, tenacity Hardness 3.5 (VHN 190–300); density 6.45 measured on synthetic material, 6.515 calculated; brittle, flexible and elastic in thin scales; a 20.00 g piece reads 16.90 g in waterWhat colour is tenorite? Steel-gray, iron-gray, black; brown in transmitted light; light gray with golden tint in reflected light. Lustre metallic. The sheet prints no streakThe black-metallic ledger 13 of 107 cached copper sheets print black in Color and metallic in Luster; 11 contain sulfur. Tenorite and paramelaconite are the two oxidesAn ore? The sheet’s word, at one locality: “an ore at Bisbee, Cochise Co., Arizona”Name For Professor Michele Tenore (1781–1861), Italian botanist, University of Naples

Tenorite is CuO, copper(II) oxide: monoclinic, steel-grey to black with a metallic lustre, hardness 3.5, density 6.45 measured on synthetic material, 79.89% copper by mass. Of 13 cached copper sheets that print a black colour and a metallic lustre, 11 contain sulfur; tenorite and paramelaconite are the two oxides. Its sheet calls it an ore at Bisbee, Arizona.

In short

  • The species. The September 2026 IMA-CNMNC Master List lists tenorite as CuO, status A, 1962 s.p., Italy. The Handbook of Mineralogy sheet gives monoclinic C2/c; lathlike crystals to 2 mm, more often scaly, dendritic or earthy; hardness 3.5; density 6.45, measured on synthetic material. Worked, CuO is 79.89% copper, the figure on is cuprite an oxide and is copper a mineral. The cell gives 6.516 against the printed 6.515.
  • What colour is tenorite? Its sheet: “Steel-gray, iron-gray, black; brown in transmitted light”, with a metallic lustre. It prints no streak. Steel-grey and black are also the colours of many copper sulfides, which is the problem the ledger below measures.
  • The black-metallic ledger. A script read the Color and Luster fields of the 107 cached Handbook sheets with copper in the header formula. 13 print black and metallic. 11 contain sulfur, among them chalcocite, enargite, tetrahedrite, tennantite, polybasite and stannite. Only tenorite and paramelaconite are oxides; the sheet set has no third.
  • Documented failure: the scale and the streak. Tenorite’s 6.45 is the highest of the 12 densities the ledger’s sheets print, but meneghinite, a lead copper antimony sulfide, prints 6.36: a 20.00 g piece reads 16.90 g against 16.86 g in water, 0.04 g apart. Paramelaconite reads 16.69 to 16.73 g. And tenorite’s streak cannot be checked against its sheet, because none is printed.
  • An ore of copper? The sheet uses the word once: “an ore at Bisbee, Cochise Co., Arizona.” It forms “Commonly in the oxidized zone of hydrothermal copper deposits” and as “a volcanic sublimate”, with cuprite, copper, chrysocolla, malachite and azurite. Questions about copper compounds and health are routed to toxic minerals in a collection; nothing here is health or safety advice.
The black-metallic ledger: every Handbook of Mineralogy sheet cached in refcache/hom (668 sheets, list frozen 18 November 2026) whose header formula contains copper and whose Color field contains “black” and Luster field the word metallic (not only submetallic): 13 of 107 copper sheets, read by script. Values as printed; in-water weight of a 20.00 g piece = 20 − 20/D on the printed measured density; a dash means the sheet prints none
MineralFormula (sheet)Sulfur in formula?Colour, as printed (start)StreakLustreHardnessDensity (meas.)20.00 g in water
TenoriteCuONo: oxideSteel-gray, iron-gray, black—Metallic3.56.45 (synthetic)16.90 g
ParamelaconiteCu1+2Cu2+2O3No: oxideBlack to purplish black, pitch-black on fracturesBrownish blackBrilliant metallic to adamantine4.56.04–6.1116.69–16.73 g
MeneghinitePb13CuSb7S24YesBlackish lead-grayShining blackBright metallic2.56.3616.86 g
Pearceite(Ag,Cu)16As2S11YesDull blackBlackMetallic36.1516.75 g
Polybasite(Ag,Cu)16Sb2S11YesIron-blackBlackMetallic2–36.116.72 g
ChalcociteCu2SYesBlackish lead-grayBlackish lead-grayMetallic2.5–35.5–5.816.36–16.55 g
DjurleiteCu31S16YesBlack—Metallic2.5–3——
Tetrahedrite(Cu,Fe,Ag,Zn)12Sb4S13YesFlint-gray to iron-black to dull blackBlack to brownMetallic, commonly splendent3–4.54.9715.98 g
Tennantite(Cu,Ag,Zn,Fe)12As4S13YesFlint-gray to iron-black—Metallic, commonly splendent3–4.54.6215.67 g
KesteriteCu2(Zn,Fe)SnS4YesGreenish blackBlackMetallic4.54.54–4.5915.59–15.64 g
StanniteCu2FeSnS4YesSteel-gray to iron-blackBlackishMetallic44.3–4.515.35–15.56 g
Villamaninite(Cu,Ni,Co,Fe)S2YesIron-blackSooty blackDull metallic4.54.4–4.515.45–15.56 g
EnargiteCu3AsS4YesGrayish black to iron-blackGrayish blackMetallic to dull34.4515.51 g
All 13—11 yes; 2 oxides—3 print none—2–4.54.45–6.45 (12 printed)15.51–16.90 g
Cuprite, for contrast (not in the 13)Cu2ONo: oxideCochineal-red … to nearly blackBrownish red, shiningAdamantine to submetallic, earthy3.5–46.1416.74 g

What is tenorite? The copper(II) oxide

Copper and oxygen, one to one. The September 2026 IMA-CNMNC Master List lists tenorite as CuO, status A (approved), 1962 s.p., country Italy. The Handbook of Mineralogy tenorite sheet writes CuO and says only “Nearly pure CuO; modern analyses are not available”, so the composition on this page is the ideal one: with Cu 63.546 and O 15.999 the formula mass is 79.55, 79.89% copper and 20.11% oxygen. Balanced against O2−, the copper is Cu2+. That is the figure on is cuprite an oxide, whose one-plus check sets tenorite beside cuprite, Cu2O, and paramelaconite; that check is not repeated here.

What the sheet records. Monoclinic, point group 2/m, space group C2/c, a = 4.6837, b = 3.4226, c = 5.1288 Å, β = 99.54°, Z = 4. Crystals are lathlike, flattened on [100] and elongated along [011], only to 2 mm; it is more often curved, scaly, dendritic, and commonly pulverulent, earthy or massive. Twinning on {011}, a contact plane, is common and forms stellate groups; also lamellar. Fracture conchoidal to uneven; brittle, but flexible and elastic in thin scales; hardness 3.5, VHN 190–300. Density 6.45 was measured on synthetic material; 6.515 is calculated.

The cell checks out. Four CuO units in a cell of 81.08 ų give 6.516, against the printed 6.515. A 20.00 g piece reads 16.90 g in water at 6.45, on the method at how to measure specific gravity at home, which is the figure is copper a mineral uses.

What colour is tenorite? The black-metallic ledger

Method. A script read every Handbook sheet cached for this site, 668 on the list frozen on 18 November 2026, and kept the 107 whose header formula contains copper. Of those, 32 have “black” somewhere in the Color field, many as blackish green. It then kept those whose Luster field uses the word metallic, not counting submetallic alone. That leaves 13: chalcocite, djurleite, enargite, kesterite, meneghinite, paramelaconite, pearceite, polybasite, stannite, tennantite, tenorite, tetrahedrite and villamaninite. Tenorite and chalcocite were the positive controls, and both are in.

Result. Eleven of the 13 formulas contain sulfur. The two without it are tenorite, CuO, and paramelaconite, Cu1+2Cu2+2O3. So a black, metallic copper mineral on these sheets is, by count, much more often a sulfur-bearing one than an oxide, and tenorite is the exception the colour hides. Cuprite is outside the 13: its sheet runs from cochineal-red “to nearly black” but prints “Adamantine to submetallic, earthy”.

Paramelaconite, the other black oxide. Its sheet, read for this page, gives tetragonal, hardness 4.5, density 6.04–6.11, streak brownish black, and “A very rare secondary mineral in hydrothermal copper deposits”, listing tenorite among its associates at the Copper Queen mine, Bisbee, and the Algomah mine, Michigan. Worked from the IMA formula it is 84.12% copper, as on is cuprite an oxide.

Can you tell tenorite from the black copper sulfides?

Documented failure: the scale. Tenorite’s measured 6.45 is the highest of the 12 measured densities in the ledger; djurleite prints none. But it is only 0.09 above meneghinite’s 6.36, a lead copper antimony sulfide: a 20.00 g piece reads 16.90 g against 16.86 g in water, 0.04 g apart. Pearceite, polybasite and paramelaconite read 16.69 to 16.75 g. Matrix, or a density measured on synthetic material rather than a natural crystal, would cover that difference.

Documented failure: the streak and the scratch. The tenorite sheet prints no streak, so a streak cannot be checked against it; the method is at how to use a streak plate. Hardness 3.5 sits inside the ledger’s span of 2 to 4.5. What the sheets do separate is chemistry and setting: tenorite has no sulfur, and its sheet places it in oxidized zones with cuprite, copper, chrysocolla, malachite and azurite. That is context, not a test, and this page gives no chemical test.

The lustre caveat. A metallic lustre is about appearance, not composition; the sulfide survey of lustre words is on is sphalerite a sulfide and is not repeated. Is tenorite metal? No: it is an oxide of copper with its own IMA row; the metal is native copper, whose sheet prints it highly malleable where tenorite’s prints brittle.

Is tenorite an ore of copper?

At one locality, in the sheet’s words. The Distribution field reads “an ore at Bisbee, Cochise Co., Arizona.” No other locality carries the word, and this page does not extend it. The Occurrence field: “Commonly in the oxidized zone of hydrothermal copper deposits; a volcanic sublimate.” The associates split the same way: cuprite, copper, chrysocolla, malachite, azurite and Fe–Mn oxides in hydrothermal deposits; copper chlorides, alkali chlorides and cotunnite at volcanoes.

Tenorite or cuprite? Both are copper oxides of the oxidized zone, and the cuprite sheet lists tenorite as an associate. Tenorite is CuO, monoclinic, steel-grey to black, metallic, 79.89% copper; cuprite is Cu2O, cubic, red to nearly black, with a brownish red streak, 88.82% copper. Worked, 1.252 kg of tenorite carries 1 kg of copper. The valence comparison is on is cuprite an oxide. Questions about copper compounds and health are routed to toxic minerals in a collection; nothing here is health or safety advice.

Where is tenorite found? The sheet’s locality list

Distribution, as printed. “Many localities, but few for well-crystallized or pure material.” From Vesuvius, Campania, and Etna, Sicily, Italy. In England, at a number of mines in Gwennap, Redruth, St. Just and elsewhere in Cornwall. At Leadhills, Lanarkshire, Scotland. From Rio Tinto, Huelva, Spain. In Germany, at Siegen, Westphalia; Daaden, Rhineland-Palatinate; Neubulach, Black Forest. At Jáchymov, Czech Republic. In Russia, Bogoslovsk and Nizhni Tagil in the Urals, and the Tolbachik fissure volcano, Kamchatka. In the USA, Copper Harbor, Keweenaw Co., Michigan; Darwin, Inyo Co., California; and Bisbee, Arizona. Chuquicamata, Chile. Tsumeb, Namibia.

Name. “To honor Professor Michele Tenore (1781–1861), Italian botanist, University of Naples.” The IMA list gives Italy as the country. More copper minerals are in the species index. We hold no catalogue and nothing here is offered for sale; the wanted list is the only commercial route.

Questions

What is tenorite made of?
Copper and oxygen: CuO on the IMA list and the Handbook of Mineralogy tenorite sheet, 79.89% copper and 20.11% oxygen by mass. The sheet notes that modern analyses are not available.
What color is tenorite?
Steel-gray, iron-gray or black, brown in transmitted light, with a metallic lustre, per its Handbook sheet. The sheet prints no streak colour.
Tenorite is an ore mineral of which metal?
Copper. Its sheet calls it “an ore at Bisbee, Cochise Co., Arizona”; it is 79.89% copper by mass. No other locality on the sheet carries the word ore.
What is the difference between tenorite and cuprite?
Tenorite is CuO, monoclinic, steel-grey to black and metallic; cuprite is Cu2O, cubic, red to nearly black, streak brownish red. A 20.00 g piece reads 16.90 g and 16.74 g in water.
Is tenorite magnetic?
Its Handbook sheet prints no magnetic property, and USGS OFR 99-529 Table 1 has no tenorite row, so this page makes no claim.